The MFE-TEMP-S3-100 provides a rugged temperature sensor. The sensor is equipped with a DS18B20 1-Wire temperature sensor embedded into the probe. The MFE-TEMP-S3-100 is directly compatible with all general purpose 1-Wire host adapters. For complete documentation on the embedded DS18B20 sensor, please refer to the manufacturer’s spec sheet.

The full temperature range is supported (55 – 125°C) by both the silicone cable and the probe.

Features

Very rugged construction
Full temperature range of the DS18B20 is supported
Low cost
Based on the DS18B20 1-Wire temperature sensor
High accuracy and resolution
Uses 1-Wire communication protocol
Compatible with most 1-Wire software
Made in Germany

Specifications

1-Wire Connection : Bare Leads
Cable : Silicone 3.0 m
Probe : Stainless Steel 100 mm
Temperature Range : -55 to 125°C
Accuracy (-10 to +85ºC) : ±0.5°C
Accuracy (-55 to +125ºC) : ±2°C
Resolution : 0.0625 to 0.5°C
Supply Voltage : 3.0 to 5.5 Volt
Active Current : 1 MilliAmp
Protection Rating : IP67 (EN 60529)

Pinouts

Green : 1-Wire data
White : 1-Wire return
Brown : Ext. Power (Vdd)

Parasitic Mode

For parasitic mode, the Vdd line must be tied to ground. External power is recommended for faster operation.

Automotive changeover relay with 5-pins and SPDT contacts suitable for general purpose automotive applications. The relay features a plastic mounting bracket and has a compact sealed construction to protect from water and damp.

• Maximum switching current: 40A
• Maximum switching voltage: 60VDC
• Coil voltage: 24VDC
• Coil power: 1.6W
• Sealed IP67 construction
• SPDT contacts
• Excellent shock and vibration resistance
• Wide temperature range
• Body dimensions: 28 x 28 x 25mm

Maximum Switching Current: 40A
Contact Rating: 40A 14VDC
Power Consumption: 1.6W
Coil Voltage: 24VDC
Pickup Voltage: 16.8VDC
Maximum Continuous Voltage: 31.5VDC
Coil Resistance: 360Ω
Contact Arrangement: SPDT
Operating Time: 10ms Max
Release Time: 5ms Max
Drop-Out Voltage: 1.2VDC
Dielectric Strength: 500VAC 1 Minute
Insulation Resistance: 100MΩ
Ambient Temperature: -40°C to +85°C

This switch is based on a mechanism that has proven itself millions of times. It is extremely rugged and durable (ball switch). The round rocker switch has a semi matt finish and red LED. Simple installation with notched retention mechanism. Secure hold in the hole due to tolerance equalization notches The LED lights up when the switch is in the on position. (This product can be used to activate our front parking sensor kits.)

Technical details:

Color: Black with red LED
Switch Rating: 16A
Two positions: ON and OFF
Connector: Spade connectors
LED: 12V DC red

Eco-driving with real-time in-cabin drivers’ behaviour feedback.

This high profile RFID device reads the popular RFID tags running in the 125 kHz band (Manchester coding). Each tag has its own unique identification number, which is sent through 1-wire bus by emulating a DS1990A iButton. The color of the cable may vary.

Features

• reads RFID tags running in the 125 kHz band
• data are sent by emulating a DS1990 iButton
• plastic casing
• standard wire ~40 cm
• M*12 thread
• bi-color LED
• joining colors green and red we get orange
• no series resistor required, simply connect LED cathode to GND
• low-cost

Programming

Supported 1-wire commands:

• 33h (Read Rom)
• F0h (Search Rom)

The emulated 64-Bit ROM consists of:

• CRC (1 Byte)
• 0x00
• RFID Serial number (5 Bytes)
• Family Code DS1990 (0x01)

Specifications

Power supply : 6.5-30 Volts
Active Current : 12mA (without LED)
Frequency : 125 kHz
Reading distance : ~4 cm
Bi-color LED : Green/Red
Active Current LED : 10 mA per color

Applications

• Cash registers
• Time and attendance
• Access control

Pinouts

Yellow : Power supply (6.5-30 volts DC)
Gray : Ground
White : 1-Wire Data
Green : Cathode green LED
Brown : Cathode red LED

RF9092Lv-Mw-xy-z

v = number of LEDs (0 = no LED)
w = LED with common Anode (A) or Cathode (K)
x = thread in millimeter (0 = no thread)
y = frequency
z = advanced feature (e.g. water resistant)

Stainless steel panel-mount probe with bi-color LED; designed for use with magnetic iButtons of the DG9093MG Series. The color of the cable and the O-ring may vary.

Features

• signal contact and grounding made of high grade stainless steel (1.4418)
• standard wire ~40 cm
• M*20 thread
• joining colors green and red we get orange
• possibility to work in Touch and Hold mode

Applications

• The food services and/or restaurant industry
• Cash registers
• Computer and data processing
• Time and attendance
• Access control

Connection Diagram

DG9092Lw-Mx-y-z

w = number of colors (LED)
x = thread in millimeter
y = material (CR=chromium, ST=stainless steel)
z = model

LV-CAN200 is designed to acquire data from light vehicles, trucks and buses. Access to CAN Bus data enables fleet operators to report on a wide range of information. You can effectively identify areas of improvement within their vehicle operation to drive down overheads and minimize environmental impact.

Technical details

• Power supply (+9…+50)V DC
• Power supply current:
  • Active mode max 50mA
  • Standby mode max 2mA
• Working temperature -40…85 °C
• Max working humidiy 85% (non condensate)
• Status LED

Supported Onboard computer data:

• Fuel consumption
• Engine RPM
• Door status
• Total mileage
• CNG status
• Accelerator pedal position
• Fuel level
• Engine temperature
• Vehicle speed
• Oil pressure

The best and only OBDII extension cable you will ever need to own. Passes all 16 pins straight through. NO shared ground wires. Ultra low profile design for hard to reach spots. Super flexible rubber coating is resistant to gas, oil, and most other common shop fluids. Highest Quality 2 piece over molded male and female plug jackets with strain relief.